The following options and accessories can be used with the Altivar 31 drive kit: Purpose designed IP55 customisable moulded enclosure version of the Altivar 31 Easy to modify panel area with the knockout covers, this allows telemecanique inverter altivar 31 user manual user to add additional components if required e.
The Altivar 12 Series frequency inverters are for use with single and 3 phase supplies and three-phase V asynchronous motors rated from 0. Sometimes Telemecanique altivar 31 instruction manual — everyone. Simple and telemecanique inverter altivar 31 user manual, the PowerSuite Software Workshop makes it easy to configure Telemecanique variable speed drives. Installation supply cables at least 31 cm.
If you visit our website hoping to find Manual Inverter Atv, we are happy to tell you that it is available in all the. Altivar 31H Installation manual Variable speed drives for asynchronous motors http: Designed for 3 phase asynchronous motors from 0. The repair will telemecaniqye done by the replacement of defective parts by new components furnished by.
Variable telemecanique inverter altivar 31 user manual drives for asynchronous motors. The Altivar 31 must be considered as a component: Variateurs de vitesse CVF pour moteurs asynchrones.
Friends of PDF all our visitors are our friends. It can be accessed in the drC- menu page 27 anytime. Configure the parameters in the drC- menu if the factory configuration is not suitable. Refer to page 10 for the factory settings. Remove power from the drive controller and follow the bus voltage measurement procedure in the ATV31 Installation Manual.
Then connect the control wiring to the logic and analog inputs. Adjust the speed reference. Failure to follow these instructions will result in death or serious injury.
Failure to follow these instructions can result in death, serious injury, or equipment damage. Failure to follow this instruction can result in equipment damage. The recommended method of control is through inputs LI1 to LI6.
The motor thermal state memory returns to zero when line power is removed from the drive controller. Power Up after a Manual Fault Reset or Stop Command If parameter tCt is at its factory setting trn , when the drive controller is powered up after a manual fault reset or a stop command, the forward, reverse, and DC injection stop commands must be reset for the drive controller to start.
If they are not reset, the drive controller will display nSt and will not start. If automatic restart is configured parameter Atr in the FLt- menu, see page 77 the reset is not necessary.
The drive controller will not provide motor thermal protection if the motor current is less than 0. The drive controller cannot provide adequate motor thermal protection for each motor. Operation on an Impedance Grounded System When using the drive controller on a system with an isolated or impedance grounded neutral, use a permanent insulation monitor compatible with non- linear loads. These filters can be disconnected from ground when using the drive controller on an impedance grounded system to increase the operating life of their capacitors.
Use the configuration settings tables beginning on page 89 to prepare and record the drive configuration before programming the drive controller. See pages 30, 33, 47, and When first commissioning an ATV31 drive controller for a 60 Hz system, perform a factory parameter reset. Be sure to set bFr to 60 Hz. Auto-tuning measures the stator resistance of the motor to optimize the control algorithms. See page In the event of an overcurrent, the drive controller trips to protect itself against overloads.
The fan starts automatically when the drive controller receives an operating direction and reference. It stops a few seconds after motor speed is less than 0. The protection is available for self-cooled motors.
NOTE: The motor thermal state memory returns to zero when line power is removed from the drive controller. Only persons with such expertise should be allowed to program, install, alter, and apply this product. The display flashes when a value is stored. The default display is motor frequency, for example In current limiting mode, the display flashes. See the following section. With the factory configuration, when the drive controller is powered up after a manual fault reset or stop command, the forward, reverse, and DC injection stop commands must be reset for the drive controller to start.
If automatic restart is configured, the reset is not necessary. If the reference channel or the control channel is assigned to Modbus or CANopen see page 34 , the drive controller will display nSt on power up and remain stopped until the communication bus sends a command.
ENT It has a cable with connectors for connection to the drive serial link refer to the manual supplied with the display. In order for the remote keypad display to be active, the tbr parameter in the COM- menu must remain at the factory setting, NOTE: Password protection has priority over the access locking switch. Placing the access locking switch in the locked position also prevents the drive settings from being accessed via the drive controller keypad. When the remote keypad display is disconnected, if the access locking switch is in the locked position, the drive controller keypad also remains locked.
Saving and Loading Configurations Up to four complete configurations can be stored in the remote keypad display and transferred to other drive controllers of the same rating. Four different operations for the same device can also be stored on the terminal. NOTE: Throughout this guide, a dash appears after menu codes to differentiate them from parameter codes.
To store the parameter value, press the key. All of the menus are drop-down type menus. Once you have reached the last parameter in a list, press the key to return to the first parameter. From the first parameter in the list, press the key to jump to the last parameter. If you have modified a parameter in a menu and you return to that menu without accessing another menu in the meantime, you will be taken directly to the parameter you last modified. See the illustration below.
If you have accessed another menu or have restarted the drive controller since the modification, you will be taken to the first parameter in the menu. See the illustration above.
Modifying this parameter also modifies the values of the following parameters: HSP page 24 , Ftd page 27 , FrS page 28 , and tFr page Functions which are not listed in the figure are fully compatible. If there is an incompatibility between functions, the first function configured will prevent the others from being configured.
Stop functions have priority over run commands. Speed references via logic command have priority over analog references. The arrow points to the function that has priority. A single input can activate several functions at the same time. For example, reverse and second ramp can be assigned to one input. When more than one function is assigned to an input, ensure that the functions are compatible. However, we recommend making modifications to the settings with the drive controller stopped.
Failure to follow these instructions can result in equipment damage. In this case, LFr can also be accessed via the drive controller keypad. LFr is reset to 0 when the drive controller is powered down. AC2 2nd acceleration ramp time See page Ensure that dEC is not set too low for the load.
Ensure that this setting is suitable for the motor and the application. ItH Current used for motor thermal protection. Refer to OLL on page 78 if you wish to suppress motor thermal protection. SEt- These parameters appear regardless of how the other menus have been configured. They only appear in the Settings menu. These parameters only appear if the corresponding function has been selected in another menu.
To facilitate programming, they can also be accessed and adjusted from the menu where the corresponding function is found. A detailed description of these functions can be found on the indicated pages.
Used to optimize torque at very low speed. Increase UFr if the torque is insufficient. To avoid operating instability, ensure that the value of UFr is not too high for a warm motor. FLG adjusts the speed ramp based on the inertia of the driven load.
If the value is too low, the response time is longer. If the value is too high, operating instability can result. After a period of acceleration or deceleration, StA adapts the return to a steady state to the dynamics of the machine. If the value is too low, overspeed or operating instability can result. If the value is too high, the response time is longer.
SLP adjusts slip compensation for fine tuning of speed regulation. IdC Level of DC injection braking current activated via a logic input or selected as a stop mode. SEt- 0 0. This function avoids a critical speed which leads to resonance. Setting the function to 0 renders it inactive. JGF Jog operating frequency See page Our website uses cookies and similar technologies to provide you with a better service while searching or placing an order, for analytical purposes and to personalise our advertising to you.
Adjustable Speed Drive Controllers. These flexible, compact modules are suitable for many applications. Our website uses cookies and similar technologies to telemecanique inverter altivar 31 user manual you with a better service while searching or placing an order, for analytical purposes and to personalise our advertising to you.
Programming Manual Data Sheet. Read these instructions carefully, and look at the equipment to become familiar with the device before trying to install, operate, or maintain it Schneider altivar 12 0.
Altivar 31 Programming manual. Login to quote this blog Login Close. Telemecanique altivar 31 manual. Telemecanique inverter pdf manual: The Altivar 31 ATV31 adjustable speed AC drive controller incorporates the latest sensorless flux vector technology into a compact, easy-to-use design for three-phase asynchronous squirrel-cage motors. This is the first release of this document. Manual Telemecanique Altivar 61 installation manual.
This is the time required for the. Drive kits are supplied with: The following options and accessories can be used with the Usser 31 drive kit: Designed for telemecanique inverter altivar 31 user manual phase asynchronous motors from 0. Altivar 31H Installation manual Variable speed drives for asynchronous motors http: Variadores de velocidad ajustable.
Variateur de vitesse pour moteur. The operating modes specific to communication relemecanique chart. Various dialogue and communication options 9, 10, 11, 12 can be used with the.
Move your mouse cursor telemecanique inverter altivar 31 user manual the bar above from left to right. Designed for 3 phase asynchronous motors from 0.
0コメント